Select or Create an osimage DefinitionΒΆ

Before creating an image on xCAT, the distro media should be prepared. That can be ISOs or DVDs.

XCAT uses copycds command to create an image which will be available to install nodes. copycds will copy all contents of Distribution DVDs/ISOs or Service Pack DVDs/ISOs to a destination directory, and create several relevant osimage definitions by default.

If using an ISO, copy it to (or NFS mount it on) the management node, and then run:

copycds <path>/<specific-distro>.iso

Note

While sle15 contains installer medium and packages medium, need copycds copy all contents of DVD1 of the installer medium and DVD1 of the packages medium, for example:

copycds SLE-15-Installer-DVD-ppc64le-GM-DVD1.iso SLE-15-Packages-ppc64le-GM-DVD1.iso

If using a DVD, put it in the DVD drive of the management node and run:

copycds /dev/<dvd-drive-name>

To see the list of osimages:

lsdef -t osimage

To see the attributes of a particular osimage:

lsdef -t osimage <osimage-name>

Initially, some attributes of osimage are assigned default values by xCAT - they all can work correctly because the files or templates invoked by those attributes are shipped with xCAT by default. If you need to customize those attributes, refer to the next section Customize osimage

Below is an example of osimage definitions created by copycds:

# lsdef -t osimage
rhels7.2-ppc64le-install-compute  (osimage)
rhels7.2-ppc64le-install-service  (osimage)
rhels7.2-ppc64le-netboot-compute  (osimage)
rhels7.2-ppc64le-stateful-mgmtnode  (osimage)

In these osimage definitions shown above

  • <os>-<arch>-install-compute is the default osimage definition used for diskful installation
  • <os>-<arch>-netboot-compute is the default osimage definition used for diskless installation
  • <os>-<arch>-install-service is the default osimage definition used for service node deployment which shall be used in hierarchical environment

Note

Additional steps are needed for ubuntu ppc64le osimages:

For pre-16.04.02 version of Ubuntu for ppc64el, the initrd.gz shipped with the ISO does not support network booting. In order to install Ubuntu with xCAT, you need to follow the steps to complete the osimage definition.

[Tips 1]

If this is the same distro version as what your management node uses, create a .repo file in /etc/yum.repos.d with contents similar to:

[local-<os>-<arch>]
name=xCAT local <os> <version>
baseurl=file:/install/<os>/<arch>
enabled=1
gpgcheck=0

This way, if you need to install some additional RPMs into your MN later, you can simply install them with yum. Or if you are installing a software on your MN that depends some RPMs from this distro, those RPMs will be found and installed automatically.

[Tips 2]

You can create/modify an osimage definition easily with any existing osimage definition, the command is

mkdef -t osimage -o <new osimage> --template <existing osimage> [<attribute>=<value>, ...]

Except the specified attributes <attribute>, the attributes of <new osimage> will inherit the values of template osimage <existing osimage>.

As an example, the following command creates a new osimage myosimage.rh7.compute.netboot based on the existing osimage rhels7.4-ppc64le-netboot-compute with some customized attributes

mkdef -t osimage -o myosimage.rh7.compute.netboot --template rhels7.4-ppc64le-netboot-compute synclists=/tmp/synclist otherpkgdir=/install/custom/osimage/myosimage.rh7.compute.netboot/3rdpkgs/ otherpkglist=/install/custom/osimage/myosimage.rh7.compute.netboot/3rd.pkglist